破碎機 1000 tonh

The correct installation of feeding device is significant for crusher to work normally. In order to let ore enter into crushing space uniformly, feeding device should be installed correctly. 16. 负荷试验 4.16 Load test 图13 Fig. 13 （1） 空转试验合格后，方可进行负荷试验。其起重能力可按表2 选择。4.5.4 Keep the base horizontal and ensure the machine work reliably otherwise it’s easy for single contact of the copper sheathing and the abnormal of grinding eccentric sleeve and water sealed device. 9 图1 Fig. 1 6. 传动轴的安装4.6 Installation of drive shaft 1 安装传动轴时应在底座与传动轴连接筒体的凸缘法兰间垫上垫片。破碎機 1000 tonh4.9.1 Clear up the protective oil coat in the shaft and spherical surface, and blow the lubri e hole and oil groove clean with wind. （2） 在锥轴表面涂一层黄干油，球面上涂一层稀油。技术特点： 1、多腔均匀破碎，适宜破碎硬岩。8 延长了炉内耐火材料的使用寿命。

破碎機 1000 tonh4.13.3 Start oil pump before starting the crusher until all lubri ion points get lubri ing then start crusher. 4 空转试验连续运转不得少于2小时。When the crusher works the motor drives the eccentric sleeve through horizontal shaft and a pair of bevel gear to rotate. The shaft axis of crushing cone is force to swing by the eccentric sleeve thus making the crusher wall and rolled mortar wall close up and far from each other now and then. Ore is crushed under continuous extrusion and bending. 四、机器的安装与试运转 4. Installation and Trial Running of Machine 1. 本说明仅包括破碎机的特殊安装说明其余可按一般机器的通用安装规程进行安装。4.11.3 Inlet pipe and outlet pipe should be installed tightly and easy to be disassembled. 4 排水管接近贮水箱处应设一个便于检查的喇叭口接水管。4.12.3 When installing crushing cone the installation of lubri ing device should be completed. The reason is that when taking test on lubri ing device at this time if there is malfunction in the lubri ion aspects it will be convenient for disassembling and repairing. 18 图12 Fig.12 13. 空转试验 4.13 Free-running test 1 在上述各部分安装完后要做没有负荷的试验检查安装的是否符合要求如发现不当的地方此时便于休整。During the disassembling after testing phenomena of copper-surfaced burn and fraying in fri ion part of the crusher shouldn’t occur. 6 假如破碎圆锥转数很可能产生不良现象应当立即停车进行检查休整。4.11.2 When installing the water pipe of dust sealing device it should be prevented from being stricken and frayed by ore. 3 进水管和排水管要安装紧密并且容易拆卸。

4.1 This specifi ion only includes the special installation instructions of crusher. While others can refer to the universal installation instruction of common machine. 2. 起重设备：4.2 Hoisting equipment 安装破碎机的厂房内，须有起重设备，以便在机器安装、修理时使用。破碎機 1000 tonh该机实用性强，破碎范围广能破碎轻薄料压块、铁皮压块、打包压块,、自行车压块、摩托车压块、汽车壳压块、废旧家电压块、彩钢瓦压块、油漆桶压块、易拉罐压块等。Repair the damaged parts of transportation. C、 检查轧臼壁和锌合金的紧固情况。Remove all dirt from the screw thread. B、 修正运输中损坏的地方。 4.7.3 After installing the hollow eccentric shaft the external endface of gear and pinion should be aligned see Fig.7 in order to inspect the clearance of gear meshing. The gear tip clearance b is 4±0.3 and the gear backlash A is 2.63.2mm. 图6 Fig. 6 12 图7 Fig. 7 8. 碗形轴承的安装 4.8 Installation of bowl-shaped bearing 1 碗形轴承架应与底座配合紧密并用塞尺检查水平接触面的紧密情况。Check whether the rolled mortar wall and zinc alloy are fastened. （2） 往支承套螺纹里装调整环时，可以使用滑车（见图14）。

【1000X1050反击式破碎机--正科机械】价格,厂家,图片,矿山机械配件,郑州市正科机械有限-马可波罗网#正科机械是破碎机，颚式破碎机，反击式破碎机，移动破碎站等矿山机械碎石机设备生产基地。Remove all dirt from the screw thread. B、 修正运输中损坏的地方。齿轮的齿顶间隙b 为4±0.3齿侧间隙A为2.63.2mm。 4.7.3 After installing the hollow eccentric shaft, the external endface of gear and pinion should be aligned (see Fig.7) in order to inspect the clearance of gear meshing. The gear tip clearance b is 4±0.3, and the gear backlash A is 2.6~3.2mm. 图6 Fig. 6 图7 Fig. 7 8. 碗形轴承的安装 4.8 Installation of bowl-shaped bearing （1） 碗形轴承架应与底座配合紧密，并用塞尺检查水平接触面的紧密情况。 4.5.1 When install the frame verticality and levelness should be strictly guaranteed. This can be realized by inspecting the base center line in the annular machined surface of base with gradienter and plumb see Fig. 2. 2 用调整楔铁调整好底座的水平后将地脚螺钉拧紧进行次灌浆。破碎機 1000 tonh4.5.3 When the secondary grout blanket indurates don’t take out the adjusting wedge from crusher base fill the interspaces with cement and then inspect according to the installation of frame 1. 4 保持底座的水平性能保证机器可靠的工作否则易使铜套单面接触研磨偏心套和引起水封装置工作不正常。

4.3.1 Count the quantity of parts before installation. Inspect and remove the damage in the machined surface of parts and in the screw thread caused during loading, unloading and transportation. Remove the protective coating made in the machined surface during packaging and the dust and dirt dropped during transportation. 4. 基础4.4 Foundation （1） 破碎机必须安装在稳固的钢筋混凝土基础上，其基础的深度由用户根据当地的地质条件决定。破碎機 1000 tonh根据破碎机的工作状况，可分成干式系统、湿式系统和半湿式系统。4.3.1 Count the quantity of parts before installation. Inspect and remove the damage in the machined surface of parts and in the screw thread caused during loading unloading and transportation. Remove the protective coating made in the machined surface during packaging and the dust and dirt dropped during transportation. 4. 基础4.4 Foundation 1 破碎机必须安装在稳固的钢筋混凝土基础上其基础的深度由用户根据当地的地质条件决定。4.9.1 Clear up the protective oil coat in the shaft and spherical surface and blow the lubri e hole and oil groove clean with wind. 2 在锥轴表面涂一层黄干油球面上涂一层稀油。4.11.4 Set up a flared water ching pipe which is easily to be checked in the outlet pipe where is close to the storage tank. 5 进水管路上应设有调整水量的阀。When the crusher works, the motor drives the eccentric sleeve through horizontal shaft and a pair of bevel gear to rotate. The shaft axis of crushing cone is force to swing by the eccentric sleeve, thus making the crusher wall and rolled mortar wall close up and far from each other now and then. Ore is crushed under continuous extrusion and bending. 四、机器的安装与试运转 4. Installation and Trial Running of Machine 1. 本说明仅包括破碎机的特殊安装说明，其余可按一般机器的通用安装规程进行安装。

半湿式系统只是在破碎需要时，进行少量喷水，防止扬尘，并无清洗。Every fri ion part should be damaged. 五、机器的维护 5. Maintenance of Machine。齿轮的齿顶间隙b 为4±0.3，齿侧间隙A为2.6~3.2mm。（见图5）4.7.1 Assemble the shim in the bottom cover before installing eccentric shaft, install the bottom pallet on the lower end of frame by hook, and then install disk, intermediate disk and lower disk in the bottom cover one by one with the hook, making the bulge of lower disk and the fovea of bottom cover match well. (see Fig.5) 图2 Fig. 2 图3 Fig.3 图4 Fig. 4 图5 Fig.5 （2） 按图6 将空偏心轴装配好，然后用M24 环首螺钉，将空偏心轴装入架体孔内，装入时要稳落，不要使齿轮受到撞击。4.11.5 Set up a water regulating valve in inlet pipeline. （6） 在进水管处应设有当破碎机停止工作时能全部排出水槽中水的装置。破碎機 1000 tonh4.4.1 Crusher must be installed on the steady ferroconcrete foundation. Depth of the foundation is decided under the local geological conditions by users. （2） 基础下部应有足够的空间，以便安装运输设备。

经过油漆桶压块破碎机破碎出来的物料作为炼钢原料有以下优点：1 炼出来的钢水化学成分稳定。破碎機 1000 tonh4 和其他废钢混合加料时，破碎钢可充填空隙，提高加料密度。湿式系统是指破碎的同时进行喷水，并且在分拣同时进行淋水清洗。4.9.3 Put the crushing cone gently into the hollow eccentric shaft, letting the spherical surface and the bowl-shaped tile of bowl-shaped bearing contact firmly to avoid damaging the taper ring and oil deflector, and install according to Fig.9. 10. 支承套和弹簧的安装 4.10 Installation of supporting sleeve and spring （1） 在装支承套之前，将螺纹内的脏物清除，并检查螺纹是否有在运输时损坏的缺陷，发现应立即纠正。同时检查给油量，然后重新试验。4.12.2 The configuration of lubri ing device must ensure lubri ing oil to be applied successfully. 3 在安装破碎圆锥时应完成润滑装置的安装。